下载中心

LabVIEW编程环境、NI软件、图像处理软件、相机驱动

当前位置：首页>技术新闻>下载中心
全部 8966 内部新闻 12 行业动态 20 视觉技术 876 图像编程 628 下载中心 7430

NI-SCOPE 3.7 Win32/64 Eng/Jpn NI示波器驱动程序SCOPE3.7

时间：2022-06-06   访问量：1289

Windows系统下（Linux和MAC系统下请自行了解清楚）NI的各种软件、模块、工具包、驱动程序，使用NI许可证管理器来激活的，绝大部分的都可以使用NI Lincense Activator来激活：NI序列号Serial Number生成激活工具NI License Activator，LabVIEW/VBAI/VDM/VAS等软件模块工具包破解工具不限版本http://pcmv.cn/thread-490-1-1.html

视觉论坛的各种NI资源，除了视觉相关的模块有使用外，大部分的都不会使用，仅提供资源不提供技术支持。资源的下载地址一般会同时提供NI官方和百度网盘的地址。某些工具包NI地址失效或没有NI地址，只能使用百度网盘地址；如果百度网盘地址失效过期，可联系论坛客服更新。NI的服务器在美国，有时候速度很慢或下载容易出错，这样会造成安装时各种错误而无法安装。建议在下载完成后，对下载资源做校验和(NI一般会提供MD5或SHA256等)验证，与官方或视觉论坛提供的校验和对比，一致就可以安装；如不一致，则需要重新下载。视觉论坛早期下载上传的资源，基本上都是正常下载的资源；2019后下载的资源，都与NI的正确校验和对比过，保证是正确的资源才上传到百度网盘。校验和工具下载地址：文件Hash计算器FHash，文件校验和验证下载文件正确性验证，MD5值计算、SHA1值计算、SHA256值计算、CRC32值计算http://pcmv.cn/thread-26524-1-1.html

NI-SCOPE 3.7 Win32/64 Eng/Jpn NI示波器驱动程序SCOPE3.7

NI-SCOPE
NI-SCOPE为使用NI示波器产品的客户提供支持。
NI-SCOPE仪器驱动可帮助您进行多记录采集、连续采集、多板同步，并利用超过50个测量和分析函数以及传统示波器的功能。NI-SCOPE是一种兼容可互换虚拟仪器(IVI)的仪器驱动程序，提供了一系列操作和属性，可以执行波形或信号发生器的功能，并包含了交互式软件前面板和示例。

Win32/64Eng/Jpn
3.7
文件大小: 1518881452 字节 (1.41 GB)
修改日期: 2011-01-12 01:37
MD5: 2a78ef090450ae05987ca0bba5cfc7bd（官方正确）
SHA1: ca816b2f8405dcb2c806d8b02ebbda37bd7d9000
SHA256: 76297f1adc7b23e9da52b374f43c16f457b126504013675f3214ac0d2d3cb7e7
CRC32: 1e02ec12

百度网盘与NI官方下载地址：

NI-SCOPE 3.7 Win32/64 Eng/Jpn NI示波器驱动程序SCOPE3.7

http://pcmv.cn/thread-26776-1-1.html?fromuid=9

(出处: 机器视觉论坛)



NI-SCOPE ReadmeVersion 3.7

September 2010


Thank you for using NI-SCOPE. This file contains important information regarding NI-SCOPE and is organized into the following sections:

New Features in NI-SCOPE 3.7

NI-SCOPE 3.6.2 adds support for LabVIEW 2010 (32-bit) and LabVIEW 2010 (64-bit).

Supported Hardware

The following table shows which hardware products are supported under particular operating systems.
Hardware ProductWindows XPWindows Vista
32-Bit		Windows Vista
64-Bit		Windows 7
32-Bit		Windows 7
64-Bit
NI PXI/PCI-5102
Yes
Yes
No
Yes
No
NI PCMCIA/USB/AT-5102*
Yes
No
No
No
No
NI PXI/PCI-5105
Yes
Yes
Yes
Yes
Yes
NI PXI/PCI-5112
Yes
Yes
No
Yes
No
NI PXI/PCI-5114
Yes
Yes
Yes
Yes
Yes
NI PXI/PXIe/PCI-5122
Yes
Yes
Yes
Yes
Yes
NI PXI/PCI-5124
Yes
Yes
Yes
Yes
Yes
NI USB-5132/5133
Yes
Yes
Yes
Yes
Yes
NI PXI/PCI-5142
Yes
Yes
Yes
Yes
Yes
NI PXI/PCI-5152
Yes
Yes
Yes
Yes
Yes
NI PXI/PCI-5153
Yes
Yes
Yes
Yes
Yes
NI PXI/PCI-5154
Yes
Yes
Yes
Yes
Yes
NI PXI-5620
Yes
Yes
No
Yes
No
NI PXI-5621
Yes
No
No
No
No
NI PXIe-5622
Yes
Yes
Yes
Yes
Yes
NI PXI-5900
Yes
Yes
Yes
Yes
Yes
NI PCI-5911
Yes
No
No
No
No
NI PXI/PCI-5922
Yes
Yes
Yes
Yes
Yes
*NI PCMCIA/USB/AT-5102 are Legacy products.
Note: MXI-4 is supported on Windows Vista/XP. MXI-3 is supported only on Windows XP.

System Requirements

This section lists the minimum system and the recommended system for using NI-SCOPE.

Supported Operating Systems

NI-SCOPE 3.7 and later supports the following operating systems:
It is recommended that you have the most recent service pack for your operating system installed. Windows 2000 users must use NI-SCOPE 3.6 or earlier.

Supported Real-Time Operating Environments

NI-SCOPE 3.7 and later supports the following real-time operating environments:

Minimum System Requirements

Recommended System

Installed File Names and Locations

File Locations

ItemInstalled Location on Windows XP/2000
and Windows 7/Vista 32-bit
NI-SCOPE<IVIROOTDIR32>Drivers iScope
NI-SCOPE Function Panel<IVIROOTDIR32>Drivers iScope iScope.fp
NI-SCOPE Examples<NIDocDir> iScopeExamples
NI-SCOPE Header files<IVIROOTDIR32>Include
NI-SCOPE Import Library files (32-bit)<IVIROOTDIR32>Lib
NI-SCOPE Import Library files (64-bit)<IVIROOTDIR32>Lib_x64
NI-SCOPE DLL (32-bit)<IVIROOTDIR32>Bin
NI-SCOPE Firmware UpdatersProgram FilesNI-DAQ pgafiles



Additional File Locations for Windows 7/Vista 64-bit

ItemInstalled Location on Windows Vista 64-bit
NI-SCOPE Function Panel<IVIROOTDIR64>Drivers iScope iScope.fp
NI-SCOPE Header files<IVIROOTDIR64>Include
NI-SCOPE Import Library files (64-bit)<IVIROOTDIR64>Lib_x64
NI-SCOPE DLL (64-bit)<IVIROOTDIR64>Bin
NI-SCOPE Firmware UpdatersProgram Files (x86)NI-DAQ pgafiles



Documentation

Most documentation is available at Start»All Programs»National Instruments»NI-SCOPE»Documentation. The documentation set is composed of the following documents:
Note: Printed copies of device specifications are shipped with each device.

Installing/Uninstalling/Modifying NI-SCOPEInstalling NI-SCOPE

This section provides information on installing NI-SCOPE and NI-DAQ and upgrading from previous versions of NI-SCOPE.
NI-SCOPE installs NI-DAQ if it is not already installed, or if an earlier version of NI-DAQ is installed. NI-DAQ support files will be installed if you have LabVIEW or LabWindows/CVI in your system. However, the only component that NI-SCOPE needs from NI-DAQ is the device driver.

Upgrading from a Previous Version of NI-SCOPE

Upgrading from NI-SCOPE 1.0 and 1.1—NI-SCOPE does not install over NI-SCOPE 1.0 or 1.1. You must uninstall these versions of NI-SCOPE before installing a later version of NI-SCOPE.
Upgrading from NI-SCOPE 1.5 and later—NI-SCOPE automatically uninstalls any previous version that is greater or equal to 1.5. If you have modified any old examples, these will be overwritten by the new versions.

Uninstalling/Modifying NI-SCOPE

For Windows XP, complete the following steps:
For Windows Vista, complete the following steps:
Do not attempt to uninstall by deleting files, which may be shared with other programs. The following additional software packages may have been installed as part of the NI-SCOPE installation. Exercise care when removing these packages because they may be used by other NI products:

Programming in NI-SCOPE

NI-SCOPE provides an intuitive, full-featured interface for programming your hardware. NI-SCOPE is IVI-Scope compliant. For more information, refer to niScopeIVIComplianceDocument.txt.

Software Examples

NI-SCOPE ships with several examples for LabVIEW, LabWindows/CVI, Measurement Studio, MSVC, Visual C++, and Microsoft Visual Basic that will help you develop your software. These examples illustrate how to perform the most common operations with your hardware. To find the examples, go to Start» Programs»National Instruments»NI-SCOPE»Examples.

NI-SCOPE Soft Front Panel

The NI-SCOPE Soft Front Panel (SFP) is a software oscilloscope application for NI high-speed digitizers. It has the following features:
The NI-SCOPE SFP demonstrates some of the capabilities of NI high-speed digitizers and enables you to start using your new digitizer immediately without the need to know a programming language. The NI-SCOPE SFP is installed by default as a feature of the NI-SCOPE installation. To remove the NI-SCOPE SFP use the Add/Remove Programs option.

Bug Fixes

The following list contains changes from earlier versions of NI-SCOPE to NI-SCOPE 3.7. If you have a Bug ID, you can search this list to validate that the issue has been fixed. This is not an exhaustive list of issues fixed in the current version of NI-SCOPE.
Bug IDFixed Issue
NI-SCOPE
232263Fixed an issue where the NI-SCOPE Express VI does not maintain input impedance configuration. Changed the Express VI so it maintains the input impedance configuration.
217159Fixed an issue where closing a Signal Express project containing an NI-SCOPE step returned an error.
185276NI-SCOPE driver now returns an error if the session is invalid.
250183Fixed an issue where the user's digital gain could not be applied properly even though it had not reached the +/-1.5 V allowed. Digital gain will now be coerced to the maximum that works for the current device and the current configuration. Users can read the Digital Gain property/attribute to find the coerced value.

Known IssuesDynamic Mode in the LabVIEW FPGA Module

Using dynamic FPGA interfaces (also known as dynamic mode) in the LabVIEW FPGA Module is not supported when using peer-to-peer streaming. Dynamic mode is enabled by default in the LabVIEW FPGA Module 2010. To disable Dynamic mode, complete the following steps:

Security Prompts

When you run setup.exe to install the software from the CD, you are prompted to choose whether you want to always trust software from National Instruments. If you do not select this option, your installation may be interrupted by one or more Microsoft Windows security dialog boxes. However, if you run setup from the command line, you will not receive this prompt, and the installer will automatically install NI's Software Publisher Certificate to your Windows Trusted Publisher Store. If you do not want to make this change to your Windows Trusted Publisher Store, do not choose this installation method.

NI PXIe-5122 and NI PXIe-5622 Firmware Update for NI-SCOPE 3.7

A firmware update for the NI PXIe-5122 is available with NI-SCOPE 3.7. This update enables peer-to-peer streaming functionality on these devices.

To update firmware, run the Firmware Updater application from one of the following locations:

This application will upgrade your firmware to the latest available that works with this driver. After the application has finished running, you will be required to power down your computer and PXIe chassis to complete the firmware update.
For more information on installing firmware updates, refer to KnowledgeBase 4MJGCSAY at ni.com/support.

NI-SCOPE P2P Example Projects Prompt for Save on Close

NI-SCOPE Peer-to-Peer examples may require you to save them after opening the examples for the first time.

Switching between Certain Trigger Slopes with NI-TClk Misses Triggers

When synchronizing NI 5105 devices with NI-TClk and switching between negative digital trigger slope and immediate trigger, the immediate trigger will time out.

Window/FFT Results Differ between NI-SCOPE and LabVIEW

If you perform a Window/FFT in NI-SCOPE, the results are slightly different compared to similar functions in LabVIEW. This is because NI-SCOPE uses a slightly different definition of Windowing than LabVIEW uses.

LabVIEW SignalExpress Does Not Allow Digital Triggering with TIS Enabled on Certain Devices

In LabVIEW SignalExpress, you cannot trigger an NI 5154 device with a digital signal if Time Interleaved Sampling (TIS) mode is enabled.

RAM Requirements for NI-SCOPE Soft Front Panel

Your system must have at least 512 MB of RAM to launch the NI-SCOPE Soft Front Panel.

NI 515x Devices and NI-TClk Synchronization

When using an NI 515x device in TIS mode with NI-TClk synchronization and an external sample clock, the devices configured as the TClk slaves may fail to respond to reference triggers.

Downgrading NI-SCOPE

If you need to downgrade the current version of NI-SCOPE to NI-SCOPE 2.1.4 or earlier, you must uninstall the current versions of NI-SCOPE and NI-DAQmx before installing the older version of NI-SCOPE. After the older version of NI-SCOPE is installed, you can then reinstall NI-DAQmx.

Function Reference Help

If you click a topic link in the NI-SCOPE Function Reference Help section of the NI High-Speed Digitizers Help, you cannot use the Back button in the HTML Help window toolbar to return to the original topic.

Using Help from LabVIEW

When linking to a topic in the NI High-Speed Digitizers Help from the context help or opening the help file from a VI within LabVIEW, the NI High-Speed Digitizers Help launches and the relevant topic displays, but the location of the topic might not be highlighted in the table of contents.

Windows Power Management

NI recommends that you disable Windows power management modes, such as sleep, standby, and hibernate, when using NI-SCOPE. These modes terminate any NI-SCOPE operation in progress. In Windows Vista or on a laptop computer, the default power management settings are likely to enable sleep mode.

LabVIEW Support for Traditional NI-DAQ

Beginning with version 7.4.2, Traditional NI-DAQ (Legacy) will install support for the latest version of LabVIEW found on the system. If you require support for more than one version of LabVIEW, complete the following steps:
You should now be able to use Traditional NI-DAQ (Legacy) with both versions of LabVIEW.
The Traditional NI-DAQ (Legacy) API is mass-compiled in LabVIEW 7.0. This will not affect the functionality of your VIs. However, LabVIEW will prompt you to save the Traditional NI-DAQ (Legacy) subVIs if your LabVIEW version is greater than 7.0. To avoid the prompts, mass-compile the folders referenced above. If you require Traditional NI-DAQ (Legacy) support for earlier versions of LabVIEW, you need an earlier version of Traditional NI-DAQ (Legacy).

NI-SCOPE Soft Front Panel Keyboard Shortcuts

Beginning with NI-SCOPE 3.1, the following shortcuts have changed in the NI-SCOPE Soft Front Panel:

NI-SCOPE Express Step in NI Signal Express 1.0

The NI-SCOPE Express step that ships with NI-SCOPE was designed for use with NI SignalExpress 1.1 or later. The NI-SCOPE Express step is compatible with NI SignalExpress 1.0 with the exception that software start triggers are not supported.

TClk Connector Alignment in NI-SCOPE 2.7 and Later

If you are using NI-TClk to synchronize non-identical devices (for example, an NI PXI-5122 with an NI PXI-5124), you will notice a change in behavior in the skew associated with synchronization when you upgrade from NI-SCOPE 2.6.1 to a later version. The new behavior compensates for delay associated with the input path. This delay varies from device to device. Because the driver now handles this delay, synchronizing any SMC-based products should produce data that has a small constant skew over all sample rates.

NI 5102

Board revision 183612F-01 of the NI PCI-5102 and board revision 184603E-01 of the NI PXI-5102 must be used with NI-SCOPE 2.6.1 or later. Board revision 183442G-01 of the NI PCMCIA-5102 must be used with NI-SCOPE 2.8 or later. To verify the board revision number, remove the device from the computer or chassis and turn it to view the side. The revision number is labeled "ASSY" and is located near the serial number. If you have an earlier version NI-SCOPE installed, go to ni.com/idnet to download the latest version.

NI 5112

You can now read data as soon as it is acquired. However, on a single record acquisition, the fetch functions do not wait for the trigger holdoff to expire. If you configure a trigger holdoff on a single record acquisition, you must make sure the trigger holdoff period has expired before initiating another acquisition. Call niScope_AcquisitionStatus to find out when the entire acquisition, including trigger holdoff, has completed.

NI 5122

NI PXI/PCI-5142, NI PXIe-5622

TClk synchronization is not fully supported for certain cases. When the DDC Enabled property or the NISCOPE_ATTR_DDC_ENABLED attribute is set to True, there are certain configurations for which shared triggers cannot be TClk synchronized. The following table explains which triggers can be TClk synchronized for different configurations. For all cases, it is assumed that the DDC is enabled. If the DDC is not enabled, there are no restrictions on TClk synchronization.
Configuration
51425622
Start Trigger
Reference Trigger
(Digital)
Reference Trigger
(Analog Edge)
Reference Trigger
(Power Edge)
Start Trigger
Reference Trigger
(Digital)
Reference Trigger
(Analog Edge)
Reference Trigger
(Power Edge)
Fractional Resampling Off, Homogeneous Sample Rates
Y
Y
Y
N
Y
Y
N/A
Y
Fractional Resampling Off, Heterogeneous Sample Rates
Y
Y
Y
N
Y
Y
N/A
N
Fractional Resampling On, Single-Record, Homogeneous Sample Rates
N/A
N/A
N/A
N/A
Y
Y
N/A
Y
Fractional Resampling On, Single-Record, Heterogeneous Sample Rates
N/A
N/A
N/A
N/A
Y
N
N/A
N
Fractional Resampling On, Multi-Record, Homogeneous Sample Rates
N/A
N/A
N/A
N/A
Y
Y
N/A
Y
Fractional Resampling On, Multi-Record, Heterogeneous Sample Rates
N/A
N/A
N/A
N/A
Y
N
N/A
N
Note: Reference triggers that cannot be TClk synchronized (such as power edge reference triggers) can still be shared between devices by exporting them using the niScope Export Signal VI or the niScope_ExportSignal function.

Link Library

NI-SCOPE 2.1.4 and previous versions installed a duplicate version of the NI-SCOPE C link library called niscope_32.lib. This duplicate version has been obsoleted and now only niscope.lib is installed. Programs linking against the duplicate name need to be changed to link against niscope.lib.

Visual Basic

ViConstString, ViChar, and ViString are used as parameters for the NI-SCOPE functions. However, these types are invalid in Visual Basic. Visual Basic users should declare variables of type String.

IVI

The trigger type (NISCOPE_ATTR_TRIGGER_TYPE) for immediate triggering used to be returned as NISCOPE_VAL_EDGE (1). It is now returned as NISCOPE_VAL_IMMEDIATE_TRIGGER (6).
Copyright
© 1999–2010 National Instruments Corporation. All rights reserved.
Under the copyright laws, this publication may not be reproduced or transmitted in any form, electronic or mechanical, including photocopying, recording, storing in an information retrieval system, or translating, in whole or in part, without the prior written consent of National Instruments Corporation.
National Instruments respects the intellectual property of others, and we ask our users to do the same. NI software is protected by copyright and other intellectual property laws. Where NI software may be used to reproduce software or other materials belonging to others, you may use NI software only to reproduce materials that you may reproduce in accordance with the terms of any applicable license or other legal restriction.
Trademarks
CVI, LabVIEW, National Instruments, NI, ni.com, the National Instruments corporate logo, and the Eagle logo are trademarks of National Instruments Corporation. Refer to the Trademark Information at ni.com/trademarks for other National Instruments trademarks.
Patents
For patents covering the National Instruments products/technology, refer to the appropriate location: Help» Patents in your software, the patents.txt file on your media, or the National Instruments Patent Notice at ni.com/patents.


上一篇：NI-SCOPE 3.5.2 Win32/64 Eng/Jpn NI示波器驱动程序SCOPE3.5.2

下一篇：NI-SCOPE 3.8.1 Win32/64 Eng/Jpn NI示波器驱动程序SCOPE3.8.1

标签：NI-SCOPE 3.7  NI示波器驱动程序3.7  可互换虚拟仪器IVI  NI-SCOPE仪器驱动  NI示波器产品 

LabVIEW视觉
联系我们
  • 电话：13450001061
  • 邮箱：84162741@qq.com
  • Q  Q：84162741

二维码

扫一扫 手机访问

Copyright © 2009-2025 www.labviewx.com LabVIEW视觉
电话咨询
在线咨询
简介

在线咨询

点击这里给我发消息 售前咨询专员

点击这里给我发消息 售后服务专员

在线咨询

免费通话

24小时免费咨询

请输入您的联系电话，座机请加区号

免费通话

微信扫一扫

微信联系
返回顶部